Skip to content
AnsweredAAbutPierQ&A #2013252006-12-07 19:44 · Views 74

Pc check in slender column check

장주의 경우 모멘트 확대계수 산정시 δns = Cm / {1 - Pu/(0.75Pc)} ≥ 1.0 0.75Pc > Pu 인 경우에는 문제가 없지만 (δns > 1) 0.75Pc < Pu 인 경우에는 δns가 음수(-) 값이 나와서 언제나 δns = 1 이 적용됩니다. 그리고 계산도 계속이어지는데.. 0.75Pc < Pu인 경우에는 기본적인 가정에 어긋나므로 이경우대한 판정을 미리 선행되어야 합니다. 검토바랍니다.

Answer2006-12-07 18:23

안녕하세요. 한길아이티입니다. δns = Cm / {1 - Pu/(0.75Pc)} ≥ 1.0 기록하신 식에서 보듯이 δns ≥ 1.0 이어야 하므로 음수가 나와 전체가 1 이하인 경우 1로 계산됩니다. 감사합니다.

Follow-up2006-12-08 17:15

δns = Cm / {1 - Pu/(0.75Pc)} 의 식에서 Cm = 1.0 (횡하중이 있는 경우) Pc = 100 으로 가정하여 Pu의 변화에 따른 δns 값을 확인해 보면 Pu = 50 -----> δns = 3.0 Pu = 70 -----> δns = 15.0 Pu = 74.499 --> δns = 149.70 (이런경우는 모멘트가 엄청커져서 기둥단면 자체를 바꿔야 겠죠) Pu = 75 -----> 분모가 0 이돼서 δns 는 무한대가 됩니다. Pu = 80 -----> δns = -15.0 ( 적용 δns = 1.0 ) Pu = 90 -----> δns = -5.0 ( 적용 δns = 1.0 ) 위에서 본것과 같이 Pu가 커지면 당연히 δns도 커지게 됩니다. 그리고 0.75Pc보다도 Pu가 커지면 위의 식 자체는 의미가 없어지게 됩니다. 왜냐하면 Pu가 50일때 보다도 Pu가 90인 경우의 모멘트 확대계수가 작다는 것은 말이 안돼는 것이거덩요 그러므로 0.75Pc < Pu 인 경우에는 단면을 키워야 합니다. 시방서에는 0.75Pc > Pu 규정이 나온 부분은 없습니다만 철근콘크리트책(학교에서 배우던) 장주편 확대모멘트 관련 내용을 보면 설명하는 그림이 있고 그 맨 윗부분에 P<Pc로 표현되어 있습니다. 말하자면 분모(Pc)가 분자(P)보다 커야만 모멘트 확대계수 산정식이 의미를 가지게 됩니다. 시방서에서는 강도감소 계수를 고려하여 0.75Pc 를 적용하고 있으므로 기둥단면은 최소한 0.75Pc > Pu가 되도록 다면조정이 되어야 한다고 생각됩니다. 혹시 이부분에 대해 좀더 자세한 규정이나 자료가 있으면 검토 부탁드리겠습니다.

More in this list

StatusProductNo.TitleViewsDate
AnsweredAAbutPier#268560Question about the calculation report1802026-09-29
AnsweredAAbutPier#268548Tendon force when placing tendons in the pier cap2182026-09-29
AnsweredAAbutPier#268520Pier seismic check2482026-09-23
AnsweredAAbutPier#268509Transverse reinforcement factor, K1922026-09-22
AnsweredAAbutPier#268492Girder positions in slab dimensions3352026-09-21
AnsweredAAbutPier#268483Transverse pile member forces are "0" in pier pile foundation check1982026-09-21
AnsweredAAbutPier#268482Top and bottom rebar detailing error in pier foundation STM2162026-09-21
AnsweredAAbutPier#268476Question about slab dimensions3062026-09-19
AnsweredAAbutPier#268470Settlement and bearing capacity2692026-09-18
AnsweredAAbutPier#268462Superstructure wind load in the calculation report1912026-09-18
AnsweredAAbutPier#268451Changing bearing location872026-09-18
AnsweredAAbutPier#268445Main rebar placement2712026-09-17
AnsweredAAbutPier#268438Modeling error in seismic analysis4042026-09-17
AnsweredAAbutPier#268433Pier alignment center1862026-09-17
AnsweredAAbutPier#268431Please check the design ground surface displacement2302026-09-17
AnsweredAAbutPier#268422Question about pier2522026-09-17
AnsweredAAbutPier#268416Wprov calculation in the structural calculation report2452026-09-17
AnsweredAAbutPier#268402Increasing the number of column main rebars3912026-09-16
AnsweredAAbutPier#268392Question about cast-in-place piles2222026-09-16
AnsweredAAbutPier#268387Error when entering reinforcing rebar1752026-09-16
Sign in to ask