Longitudinal step at P6 superstructure type change point is not applied
상부(PSC BOX)형식중에 교좌면 부분이 LEVEL로 적용되는 TYPE밖에 없어서(설계중인 교량은 BOX하면이 LEVEL이 아니며 구배에 대한 경사는 SOLE PLATE로 LEVEL조정) 임의로 형고를 유지하기 위하여 2개의 박스(원래 한개의 박스)로 입력을 하였는데 그것때문인지 아니면 벽식 중공형이라 적용이 안되는건지.. 아무리 적용하려 해도 되질 않습니다... 뒷부분 P10 이외의 구간은 종단 단차가 적용되는데.. 프로그램상의 버그인지 검토 바랍니다.. 참고로 일반 자료만 입력된 상태로 아직 단면검토는 되지 않은 상태입니다...
안녕하세요. 한길아이티입니다. 질문하신 내용을 정확히 파악하지 못하여 첨부파일을 검토하려 했으나 잘못된 파일이 첨부된 것같습니다. 파일 용량이 8byte인 것으로 보아 정상적인 파일이 아닌 것으로 판단되며 프로그램상에서 열리지 않습니다. 파일을 다시 첨부하여 주시면 추가로 검토후 답변드리겠습니다. 감사합니다.
Follow-up2006-02-06 10:13
파일만 다시 올립니다..
안녕하세요. 한길아이티입니다. 종방향 변단면의 적용은 두부보의 단차로 적용이 됩니다. P6의 경우는 두부보가 없는 형태이어서 종방향의 단차가 적절히 적용되기 어렵습니다. 적용을 하시려면 기둥폭과 같은 두부보를 임의로 만드신 후에 종방향 단차를 적용하시면 됩니다. 이 경우 두부보에 대한 철근이 생성이 되어 철근제원 및 배근도상에서 일정부분 작업을 해주셔야 합니다. 답변을 보신 후 다른 사항이시면 게시판에 남겨주시기 바랍니다. 감사합니다.
Attachments on this post were deleted after the retention period (3 years after the last answer) and can no longer be downloaded. If you need the same material, please contact us.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | AAbutPier | #268560 | Question about the calculation report | 180 | 2026-09-29 |
| Answered | AAbutPier | #268548 | Tendon force when placing tendons in the pier cap | 218 | 2026-09-29 |
| Answered | AAbutPier | #268520 | Pier seismic check | 248 | 2026-09-23 |
| Answered | AAbutPier | #268509 | Transverse reinforcement factor, K | 192 | 2026-09-22 |
| Answered | AAbutPier | #268492 | Girder positions in slab dimensions | 335 | 2026-09-21 |
| Answered | AAbutPier | #268483 | Transverse pile member forces are "0" in pier pile foundation check | 198 | 2026-09-21 |
| Answered | AAbutPier | #268482 | Top and bottom rebar detailing error in pier foundation STM | 216 | 2026-09-21 |
| Answered | AAbutPier | #268476 | Question about slab dimensions | 306 | 2026-09-19 |
| Answered | AAbutPier | #268470 | Settlement and bearing capacity | 269 | 2026-09-18 |
| Answered | AAbutPier | #268462 | Superstructure wind load in the calculation report | 191 | 2026-09-18 |
| Answered | AAbutPier | #268451 | Changing bearing location | 87 | 2026-09-18 |
| Answered | AAbutPier | #268445 | Main rebar placement | 289 | 2026-09-17 |
| Answered | AAbutPier | #268438 | Modeling error in seismic analysis | 404 | 2026-09-17 |
| Answered | AAbutPier | #268433 | Pier alignment center | 186 | 2026-09-17 |
| Answered | AAbutPier | #268431 | Please check the design ground surface displacement | 234 | 2026-09-17 |
| Answered | AAbutPier | #268422 | Question about pier | 262 | 2026-09-17 |
| Answered | AAbutPier | #268416 | Wprov calculation in the structural calculation report | 249 | 2026-09-17 |
| Answered | AAbutPier | #268402 | Increasing the number of column main rebars | 391 | 2026-09-16 |
| Answered | AAbutPier | #268392 | Question about cast-in-place piles | 222 | 2026-09-16 |
| Answered | AAbutPier | #268387 | Error when entering reinforcing rebar | 175 | 2026-09-16 |