About girder layout in clothoid sections
지점각도 입력에서 적용 부산방향,언양방향을 했는데... ,가 서로 다른데 위치와 길이를 같게 할수 없는지... 에서 L1~L4의 길이가 방향별로 다른데 맞게 적용된건지... 에서 S1,P11~P32를 사용자 임의로 조정한것인데 맞게 적요 된거지 확인부탁드립니다... 클로소이드 구간에 빔배치하다 보닌까 몰라서 이렇게 해보고 확인부탁드립니다... 수고하세요 ^..^ ~ ~
안녕하세요. 한길아이티입니다. 지점각도 입력에서 적용 부산방향,언양방향을 했는데... ,가 서로 다른데 위치와 길이를 같게 할수 없는지... => 현재 거더 배치를 P2 를 기준으로 배치를 하신것 같습니다. 현재처럼 상하행선으로 나뉘어져서 도로중심에서 좌, 우측으로 되어 있는 경우 각 슈의 해당 Station 이 틀려지므로서 말씀하신 것과 같이 시점측 위치나 교량총길이는 일치할 수 없습니다. 이것은 오로지 수학적 계산(편구배, 종단구배 등의영향)으로만 배치된 것으로 사용자가 원하는 형태를 만드실려면 수학적 계산에는 다소 위배되지만 설계자의 허용 판단에 근거하여 임의수정을 하여야 합니다. 하지만 시점 Station 이나 지간 변경은 슈 좌표에 영향을 줄 수 있는 요소이므로 슈좌표의 변동 연관성을 반드시 확인하셔야 합니다. 에서 L1~L4의 길이가 방향별로 다른데 맞게 적용된건지... => 위에 설명한데로 수치적 계산에 의해서 다르게 적용된 것입니다. 에서 S1,P11~P32를 사용자 임의로 조정한것인데 맞게 적요 된거지 확인부탁드립니다... => 지간구성에서 입력한 값은 거더배치 후 슈 좌표가 결정이되면 의미가 없어지는 수치입니다. 그래서 통상적으로 임의로 입력을 하신 후 거더배치를 합니다. 현재 입력하신 절차가 큰 무리가 없는듯 합니다. 클로소이드 구간에 빔배치하다 보닌까 몰라서 이렇게 해보고 확인부탁드립니다... 수고하세요 ^..^ ~ ~ 감사합니다.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | AAbutPier | #268560 | Question about the calculation report | 180 | 2026-09-29 |
| Answered | AAbutPier | #268548 | Tendon force when placing tendons in the pier cap | 218 | 2026-09-29 |
| Answered | AAbutPier | #268520 | Pier seismic check | 248 | 2026-09-23 |
| Answered | AAbutPier | #268509 | Transverse reinforcement factor, K | 192 | 2026-09-22 |
| Answered | AAbutPier | #268492 | Girder positions in slab dimensions | 335 | 2026-09-21 |
| Answered | AAbutPier | #268483 | Transverse pile member forces are "0" in pier pile foundation check | 198 | 2026-09-21 |
| Answered | AAbutPier | #268482 | Top and bottom rebar detailing error in pier foundation STM | 216 | 2026-09-21 |
| Answered | AAbutPier | #268476 | Question about slab dimensions | 306 | 2026-09-19 |
| Answered | AAbutPier | #268470 | Settlement and bearing capacity | 269 | 2026-09-18 |
| Answered | AAbutPier | #268462 | Superstructure wind load in the calculation report | 191 | 2026-09-18 |
| Answered | AAbutPier | #268451 | Changing bearing location | 88 | 2026-09-18 |
| Answered | AAbutPier | #268445 | Main rebar placement | 289 | 2026-09-17 |
| Answered | AAbutPier | #268438 | Modeling error in seismic analysis | 404 | 2026-09-17 |
| Answered | AAbutPier | #268433 | Pier alignment center | 186 | 2026-09-17 |
| Answered | AAbutPier | #268431 | Please check the design ground surface displacement | 234 | 2026-09-17 |
| Answered | AAbutPier | #268422 | Question about pier | 262 | 2026-09-17 |
| Answered | AAbutPier | #268416 | Wprov calculation in the structural calculation report | 250 | 2026-09-17 |
| Answered | AAbutPier | #268402 | Increasing the number of column main rebars | 391 | 2026-09-16 |
| Answered | AAbutPier | #268392 | Question about cast-in-place piles | 222 | 2026-09-16 |
| Answered | AAbutPier | #268387 | Error when entering reinforcing rebar | 175 | 2026-09-16 |