Bearing rebar quantity differs from calculation report
안녕하세요..[개인정보] 구조부의 [개인정보]입니다. 다름이 아니라..교좌받침 철근량이 계산서랑 상이하여 글을 올립니다.. P3번의 경우에는 조인트가 있는 부분인데..교좌받침 철근량을 프로그램 상에서 보여주는 것과 계산서에 출력된 것이 다르더군요...프로그램상에서는 OK로 판정되었는데.. 계산서에는 NG로 나와 있어 비교해 보니..교축방향으로 슈가 2개 있는 것을 1개로 보고 계산을 했더군요...그렇다면..프로그램에서도 그렇게 보이도록 해야 하지 않나요.. 또한, 교각 4번의 경우 프로그램상에는 분명 교좌받침 철근량에 문제가 없는 것으로 나오는데.. 계산서에는 NG가 있고....확인해 보니...철근량이 프로그램에서 잘못 보여주고 있는 것 같네요.. 교좌받침부 철근량 산정시 프로그램에서 보여주는 창에 다소 문제가 있는 것 같습니다. 지난번까지는 일일이 계산서랑 맞춰보고 수정하였는데....확인 좀 부탁드립니다.
안녕하세요. 한길아이티입니다. 1. AAbutPier에서의 받침에 대한 검토는 받침 한개에 대해서 되고 있습니다. 즉, 블럭이 병합되어 두개의 받침을 받치는 경우에도 받침하나에 대한 하중과 입력된 철근량의 1/2로 검토가 됩니다. 2. 사용철근량은 설계검토와 출력된 계산서와 일치하고 있습니다. 필요철근량의 경우는 설계검토와 계산서상의 값이 차이가 발생할 수 있습니다. 계산서의 출력은 옵션에 따라 적용이 되며 선택사항이 "최대 수직력,수평력을 조합"하는 경우는 각각의 받침에 대하여 검토한 것과는 차이가 발생할 수 있습니다. 이에 대한 옵션은 교대,교각이 [설계환경]-"설계선택사항"에서 조정하시면 됩니다. 검토상에서 모두 O.K이나 계산서상에 N.G가 날 수 있는 것도 선택사항이 각각의 최대값을 조합한 경우에는 가능한 사항입니다. 3. 검토과정에서 받침이 병합된 경우 후열의 검토가 설계검토시 나타나지 않는 부분은 수정하였습니다. 답변사항은 확인하여 보시고 이상이 있으시거나 다른 사항이시면 게시판에 남겨주시기 바랍니다. 감사합니다.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | AAbutPier | #268560 | Question about the calculation report | 180 | 2026-09-29 |
| Answered | AAbutPier | #268548 | Tendon force when placing tendons in the pier cap | 218 | 2026-09-29 |
| Answered | AAbutPier | #268520 | Pier seismic check | 248 | 2026-09-23 |
| Answered | AAbutPier | #268509 | Transverse reinforcement factor, K | 192 | 2026-09-22 |
| Answered | AAbutPier | #268492 | Girder positions in slab dimensions | 335 | 2026-09-21 |
| Answered | AAbutPier | #268483 | Transverse pile member forces are "0" in pier pile foundation check | 198 | 2026-09-21 |
| Answered | AAbutPier | #268482 | Top and bottom rebar detailing error in pier foundation STM | 216 | 2026-09-21 |
| Answered | AAbutPier | #268476 | Question about slab dimensions | 306 | 2026-09-19 |
| Answered | AAbutPier | #268470 | Settlement and bearing capacity | 269 | 2026-09-18 |
| Answered | AAbutPier | #268462 | Superstructure wind load in the calculation report | 191 | 2026-09-18 |
| Answered | AAbutPier | #268451 | Changing bearing location | 88 | 2026-09-18 |
| Answered | AAbutPier | #268445 | Main rebar placement | 291 | 2026-09-17 |
| Answered | AAbutPier | #268438 | Modeling error in seismic analysis | 404 | 2026-09-17 |
| Answered | AAbutPier | #268433 | Pier alignment center | 186 | 2026-09-17 |
| Answered | AAbutPier | #268431 | Please check the design ground surface displacement | 234 | 2026-09-17 |
| Answered | AAbutPier | #268422 | Question about pier | 264 | 2026-09-17 |
| Answered | AAbutPier | #268416 | Wprov calculation in the structural calculation report | 251 | 2026-09-17 |
| Answered | AAbutPier | #268402 | Increasing the number of column main rebars | 391 | 2026-09-16 |
| Answered | AAbutPier | #268392 | Question about cast-in-place piles | 222 | 2026-09-16 |
| Answered | AAbutPier | #268387 | Error when entering reinforcing rebar | 175 | 2026-09-16 |