Several points about AAbutPier
APIER 1) 슬래브 제원입력에서 상부슬래브 구분을 3등분만 하고 싶은데 꼭 4등분으로 되네요(첨부화일 지점2를 참고하세요) 2) 또한 양 끝의 일정구간을 LEVEL처리 했는데 정면도 제원에서 보면 EL값이 1MM정도 차이가 납니다 3) 교좌면 제원부분에서 "교량받침제원참조"에 들어 있지 않은 제원을 넣을시엔 허용수평력이 "0"이 나오는데 임으로 허용수평력을 넣을수는 없는지요? 수고하세요
안녕하세요. 한길아이티입니다. 1) 슬래브 제원입력에서 상부슬래브 구분을 3등분만 하고 싶은데 꼭 4등분으로 되네요(첨부화일 지점2를 참고하세요) => 횡단구성입력은 도로중심을 기준으로 좌우로 입력이 되고 있습니다. 입력하신 레벨구간의 경우 도로중심을 사이에 두고 있어서 프로그램내에서 자동으로 분할을 하고 있습니다. 보내주신 파일의 경우는 분할을 하지않아도 문제가 없으나 도로중심을 기준으로 구배가 변하는 경우는 문제가 발생하여 자동분할로 처리하고 있습니다. 2) 또한 양 끝의 일정구간을 LEVEL처리 했는데 정면도 제원에서 보면 EL값이 1MM정도 차이가 납니다 => 양끝단의 EL은 대칭구조이더라도 SKEW가 있는 경우 종단에 의해서 일정한 값의 차이가 발생할 수 있습니다. 3) 교좌면 제원부분에서 "교량받침제원참조"에 들어 있지 않은 제원을 넣을시엔 허용수평력이 "0"이 나오는데 임으로 허용수평력을 넣을수는 없는지요? => 참조를 하지않는 경우 [교대설계환경]-"지진하중"에서 허용수평력을 직접입력하여 주시면 됩니다. 감사합니다.
Attachments on this post were deleted after the retention period (3 years after the last answer) and can no longer be downloaded. If you need the same material, please contact us.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | AAbutPier | #268560 | Question about the calculation report | 181 | 2026-09-29 |
| Answered | AAbutPier | #268548 | Tendon force when placing tendons in the pier cap | 221 | 2026-09-29 |
| Answered | AAbutPier | #268520 | Pier seismic check | 257 | 2026-09-23 |
| Answered | AAbutPier | #268509 | Transverse reinforcement factor, K | 202 | 2026-09-22 |
| Answered | AAbutPier | #268492 | Girder positions in slab dimensions | 338 | 2026-09-21 |
| Answered | AAbutPier | #268483 | Transverse pile member forces are "0" in pier pile foundation check | 203 | 2026-09-21 |
| Answered | AAbutPier | #268482 | Top and bottom rebar detailing error in pier foundation STM | 224 | 2026-09-21 |
| Answered | AAbutPier | #268476 | Question about slab dimensions | 312 | 2026-09-19 |
| Answered | AAbutPier | #268470 | Settlement and bearing capacity | 274 | 2026-09-18 |
| Answered | AAbutPier | #268462 | Superstructure wind load in the calculation report | 193 | 2026-09-18 |
| Answered | AAbutPier | #268451 | Changing bearing location | 88 | 2026-09-18 |
| Answered | AAbutPier | #268445 | Main rebar placement | 294 | 2026-09-17 |
| Answered | AAbutPier | #268438 | Modeling error in seismic analysis | 411 | 2026-09-17 |
| Answered | AAbutPier | #268433 | Pier alignment center | 189 | 2026-09-17 |
| Answered | AAbutPier | #268431 | Please check the design ground surface displacement | 235 | 2026-09-17 |
| Answered | AAbutPier | #268422 | Question about pier | 267 | 2026-09-17 |
| Answered | AAbutPier | #268416 | Wprov calculation in the structural calculation report | 254 | 2026-09-17 |
| Answered | AAbutPier | #268402 | Increasing the number of column main rebars | 398 | 2026-09-16 |
| Answered | AAbutPier | #268392 | Question about cast-in-place piles | 226 | 2026-09-16 |
| Answered | AAbutPier | #268387 | Error when entering reinforcing rebar | 180 | 2026-09-16 |