Drawing frames are not generated properly
1. 첨부 dxf화일로 도각화일을 만들었는데, 아래선이 깨집니다. 첨부 참조. 2. xref로 도각을 사용할 시 abutpier에서 안보이고 네모 박스만 보이는데 원래 그런가요? 그렇다면 배치를 할때 문제가 생길텐데...
안녕하세요. 한길아이티입니다. DWG파일을 첨부하여 주시면 검토후 답변드리겠습니다. 감사합니다.
Follow-up2005-03-23 15:32
DWG 화일을 송부합니다. 안녕하세요. 한길아이티입니다. DWG파일을 첨부하여 주시면 검토후 답변드리겠습니다. 감사합니다.
안녕하세요. 한길아이티입니다. 1. 아래선이 깨어지는 것은 인식하지 않는 폴리라인오류가 있었습니다. 이문제는 기존의 폴리라인을 조금 변형함으로서 해결할 수 있습니다. 또한 MTEXT 는 지원하지 않으며, dxf 를 만드실때 가급적이면 Purge를 시키신 후 하시기 바랍니다. 자세한 사항은 "HowTo 기술자료의 ABorder 질의응답 사례모음"을 참조하시기 바랍니다. 2. xref 도각에 대한 사용법이 잘못되어신것 같습니다. xref도각을 사용하더라도 dgk 파일을 생성하셔서 넣어주셔야 하며, dxf 출력시 xref 파일에서 입력한 dwg 파일로 변환되어 저장됩니다. 또한 반드시 좌측 하단이 0,0 을 기준으로 제작된 dwg 도각파일이 존재하여야 합니다. 참고로 변환한 dwg 파일을 첨부합니다. 감사합니다.
Attachments on this post were deleted after the retention period (3 years after the last answer) and can no longer be downloaded. If you need the same material, please contact us.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | AAbutPier | #268560 | Question about the calculation report | 181 | 2026-09-29 |
| Answered | AAbutPier | #268548 | Tendon force when placing tendons in the pier cap | 221 | 2026-09-29 |
| Answered | AAbutPier | #268520 | Pier seismic check | 257 | 2026-09-23 |
| Answered | AAbutPier | #268509 | Transverse reinforcement factor, K | 202 | 2026-09-22 |
| Answered | AAbutPier | #268492 | Girder positions in slab dimensions | 346 | 2026-09-21 |
| Answered | AAbutPier | #268483 | Transverse pile member forces are "0" in pier pile foundation check | 203 | 2026-09-21 |
| Answered | AAbutPier | #268482 | Top and bottom rebar detailing error in pier foundation STM | 224 | 2026-09-21 |
| Answered | AAbutPier | #268476 | Question about slab dimensions | 312 | 2026-09-19 |
| Answered | AAbutPier | #268470 | Settlement and bearing capacity | 274 | 2026-09-18 |
| Answered | AAbutPier | #268462 | Superstructure wind load in the calculation report | 193 | 2026-09-18 |
| Answered | AAbutPier | #268451 | Changing bearing location | 88 | 2026-09-18 |
| Answered | AAbutPier | #268445 | Main rebar placement | 297 | 2026-09-17 |
| Answered | AAbutPier | #268438 | Modeling error in seismic analysis | 411 | 2026-09-17 |
| Answered | AAbutPier | #268433 | Pier alignment center | 189 | 2026-09-17 |
| Answered | AAbutPier | #268431 | Please check the design ground surface displacement | 237 | 2026-09-17 |
| Answered | AAbutPier | #268422 | Question about pier | 269 | 2026-09-17 |
| Answered | AAbutPier | #268416 | Wprov calculation in the structural calculation report | 256 | 2026-09-17 |
| Answered | AAbutPier | #268402 | Increasing the number of column main rebars | 398 | 2026-09-16 |
| Answered | AAbutPier | #268392 | Question about cast-in-place piles | 226 | 2026-09-16 |
| Answered | AAbutPier | #268387 | Error when entering reinforcing rebar | 180 | 2026-09-16 |