Skip to content
AnsweredACulvertQ&A #2267702005-10-05 10:55 · Views 141

Please review

결과물에서...지진시 (SI단위계에서) h,D값이 "60"으로 나오네요.. 그리고 값이 다르게 들어가는 오류 패치해도 안고쳐지는데...오피스 엑스피라 그런가..흠... 1. * 압발전단응력(τv) 검토 (상시) τv = 1210396.882 / (π x (600.00 + 600.00) x 600.00 ) = 0.535 MPa ≤ τa3 = 1.070 MPa ∴ O.K * 압발전단응력(τv) 검토 (지진시) τv = 124870.000 / (π x (600.00 + 60.00) x 60.00 ) = 5500.000 MPa > τa3 = 1.423 MPa ∴ N.G 2. b. 확대기초 단부 말뚝에 대한 수평압발전단응력 h : 수평방향의 압발전단에 저항하는 확대기초의 유효두께 (mm) * 수평압발전단응력(fch) 검토 (상시) τh = 679.309 / (450.00 x (200.00 + 600.00 + 900.00)) = 0.001 MPa ≤ τa3 = 1.070 MPa ∴ O.K * 수평압발전단응력(fch) 검토 (지진시) τh = 83657.401 / (450.00 x (200.00 + 60.00 + 900.00)) = 0.109 MPa ≤ τa3 = 1.423 MPa ∴ O.K 3. * 수직지압응력(fcv) 검토 (지진시) fcv = 1[주민]545[전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화]00000.000 / (π/4 x 600.00 ²) = [주민]4[전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화][전화]00.000 MPa > fca = 11.638 MPa ∴ N.G

Answer

안녕하세요. 한길아이티입니다. SI 단위오류는 수정하도록 하겠으며,값이 이상하게 나오는 데이터는 저의쪽에서도 다른 시스템에서 테스트 한후 수정하여 패치에 적용하도록 하겠습니다. 감사합니다.

More in this list

StatusProductNo.TitleViewsDate
AnsweredACulvert#268543Pile calculation report3292026-09-28
AnsweredACulvert#268536Setting section changes in culvert1712026-09-28
AnsweredACulvert#268524Design check not performed at wall center2152026-09-27
AnsweredACulvert#268523Applying moving vehicle loads2352026-09-27
AnsweredACulvert#268522Question about pile layout2612026-09-23
AnsweredACulvert#268521Question about features1292026-09-23
AnsweredACulvert#268510Question about joint check in Excel report output1842026-09-22
AnsweredACulvert#268499Error in STM analysis of corner region1422026-09-22
AnsweredACulvert#268471Launching the culvert program592026-09-18
AnsweredACulvert#268442All lines are displayed as dashed lines, what should I do?1392026-09-17
AnsweredACulvert#268429Question about U-type underpass1262026-09-17
AnsweredACulvert#268424Load position when applying railway loads to an underpass2342026-09-17
AnsweredACulvert#268417Changing girder dimensions1502026-09-17
AnsweredACulvert#268396Incorrect section check location for horizontal rebar1782026-09-16
AnsweredACulvert#268376Question about segment settings for U-type retaining wall1892026-09-15
AnsweredACulvert#268343Question about culvert drawing output1282026-09-15
AnsweredACulvert#268337Inquiry about checking retaining-wall-type wing walls3032026-09-14
AnsweredACulvert#268330About drawing output1512026-09-14
AnsweredACulvert#268318Some blocks not displayed1382026-09-14
AnsweredACulvert#268317Tank load for surcharge and moving loads3352026-09-14
Sign in to ask