About piles
말뚝설계와 관련해서 계산서에 문제점이 있습니다. 참고로 PHC, 타입방식입니다. 그리고 제원참조에 D=800, B TYPE을 적용했습니다. 그리고, 다음 내용은 말뚝의 스프링계수와 파일검토에 관한 내용입니다. SI단위로 수행하였습니다. 1. 1) 말뚝의 제원에서 말뚝의 탄성계수가 E = 210000.0 MPa로 되어있고, 말뚝의 단면2차 모멘트는 I = π/64 x (796.00⁴- 580.00⁴) = 15418640000.0 mm⁴로 산정되어있습니다. 확인부탁드립니다. 2. 4) 말뚝의 축직각방향 스프링정수에서 계산치 1/β(m)가 2.705로 산정되었는데, 밑에 β = 0.00004 m-1로 산정되었습니다. 확인부탁드립니다. 3. 1, 2번과 같은 이유로 스프링정수들이 5배정도 많이 산정되었는 것 같습니다. 그리고 단위도 다시 확인부탁드립니다. 하부설계기준에 나와 있는 단위와 상이합니다. (SI단위로 수정하더라도 이상합니다.) 4. 파일검토에서도 위와 같은 내용을 확인해 주시고, 5) 말뚝의 안정성 검토에서 쉘 테두리가 이상하게 나옵니다. 5. 나) 말뚝의 허용 수평지지력 검토에서 "평상시 : 말뚝의 허용 수평변위 δa1 = 15.0 > δ = 0.151 O.K !!! .... mm"로 출력됩니다. "mm"를 앞으로 옮겨주세요 6. 6) 말뚝과 확대기초의 결합부 검토에서 "수직지압응력(fcv) 검토 (지진시)"와 "압발전단응력(τv) 검토 (지진시)"에서 fcv와 τv가 이상하게 출력됩니다.
안녕하세요. 한길아이티입니다. 올려 주신 내용에 오류를 확인하여 패치에 적용토록 하겠습니다. 감사합니다.
More in this list
| Status | Product | No. | Title | Views | Date |
|---|---|---|---|---|---|
| Answered | ACulvert | #268543 | Pile calculation report | 329 | 2026-09-28 |
| Answered | ACulvert | #268536 | Setting section changes in culvert | 173 | 2026-09-28 |
| Answered | ACulvert | #268524 | Design check not performed at wall center | 216 | 2026-09-27 |
| Answered | ACulvert | #268523 | Applying moving vehicle loads | 236 | 2026-09-27 |
| Answered | ACulvert | #268522 | Question about pile layout | 261 | 2026-09-23 |
| Answered | ACulvert | #268521 | Question about features | 130 | 2026-09-23 |
| Answered | ACulvert | #268510 | Question about joint check in Excel report output | 184 | 2026-09-22 |
| Answered | ACulvert | #268499 | Error in STM analysis of corner region | 142 | 2026-09-22 |
| Answered | ACulvert | #268471 | Launching the culvert program | 59 | 2026-09-18 |
| Answered | ACulvert | #268442 | All lines are displayed as dashed lines, what should I do? | 139 | 2026-09-17 |
| Answered | ACulvert | #268429 | Question about U-type underpass | 126 | 2026-09-17 |
| Answered | ACulvert | #268424 | Load position when applying railway loads to an underpass | 236 | 2026-09-17 |
| Answered | ACulvert | #268417 | Changing girder dimensions | 152 | 2026-09-17 |
| Answered | ACulvert | #268396 | Incorrect section check location for horizontal rebar | 180 | 2026-09-16 |
| Answered | ACulvert | #268376 | Question about segment settings for U-type retaining wall | 191 | 2026-09-15 |
| Answered | ACulvert | #268343 | Question about culvert drawing output | 128 | 2026-09-15 |
| Answered | ACulvert | #268337 | Inquiry about checking retaining-wall-type wing walls | 304 | 2026-09-14 |
| Answered | ACulvert | #268330 | About drawing output | 153 | 2026-09-14 |
| Answered | ACulvert | #268318 | Some blocks not displayed | 139 | 2026-09-14 |
| Answered | ACulvert | #268317 | Tank load for surcharge and moving loads | 337 | 2026-09-14 |