Skip to content
AnsweredACulvertQ&A #2261662005-05-27 09:32 · Views 114

Allowable stress of corner reinforcement?

수고하십니다. 우각부 보강철근 검토시 허용응력이 025√fck 로 되어있는데.... - 콘크리트 허용전단응력 : 0.25√fck - 콘크리트 허용휨인장응력 : 0.42√fck 우각부 보강철근 검토시 허용휨인장응력 0.42√fck 로 하는 것이 옳다고 생각됩니다... 검토 바랍니다...

Answer2005-05-27 10:10

안녕하세요. 한길아이티입니다. 콘크리트 구조설계기준해설(2000년) 편 p326 에 보시면 "허용전단응력"을 넘는 경우라고 나와있습니다. 감사합니다.

Follow-up2005-05-30 17:06

라멘 우각부에 발생하는 응력은 도로교 설계기준해설(p.718, 그림4.12.7) 처럼 휨인장응력과 휨압축응력이고 ftmax 는 인장응력 최대값 이므로 허용휨인장응력(fta=0.42√fck), 허용휨압축응력(fta=0.40√fck) 을 적용함이 옳다고 생각되며, 콘크리트 구조설계기준에서 서술한 내용은 계수하중작용시 계수인장응력 ft가 1.06√fck 를 넘을 경우 철근을 배치하여야 한다. (인장응력이 계수하중 작용시 콘크리트의 허용되는 전단응력을 넘을경우 철근배치) 라는 내용인데 우각부 설계는 계수하중값이 아닌 사용하중값으로 검토를 하는데 위사항으로 보고 0.25√fck를 적용하는것은 생각해 봐야한다고 봅니다. 참고로 부산대학교 [개인정보] 교수님이 저술하신 교량공학에는 (fta=0.42√fck)를 적용함... 답변 부탁드립니다.

More in this list

StatusProductNo.TitleViewsDate
AnsweredACulvert#268543Pile calculation report3292026-09-28
AnsweredACulvert#268536Setting section changes in culvert1742026-09-28
AnsweredACulvert#268524Design check not performed at wall center2172026-09-27
AnsweredACulvert#268523Applying moving vehicle loads2382026-09-27
AnsweredACulvert#268522Question about pile layout2612026-09-23
AnsweredACulvert#268521Question about features1302026-09-23
AnsweredACulvert#268510Question about joint check in Excel report output1852026-09-22
AnsweredACulvert#268499Error in STM analysis of corner region1442026-09-22
AnsweredACulvert#268471Launching the culvert program592026-09-18
AnsweredACulvert#268442All lines are displayed as dashed lines, what should I do?1402026-09-17
AnsweredACulvert#268429Question about U-type underpass1262026-09-17
AnsweredACulvert#268424Load position when applying railway loads to an underpass2372026-09-17
AnsweredACulvert#268417Changing girder dimensions1522026-09-17
AnsweredACulvert#268396Incorrect section check location for horizontal rebar1832026-09-16
AnsweredACulvert#268376Question about segment settings for U-type retaining wall1932026-09-15
AnsweredACulvert#268343Question about culvert drawing output1282026-09-15
AnsweredACulvert#268337Inquiry about checking retaining-wall-type wing walls3062026-09-14
AnsweredACulvert#268330About drawing output1532026-09-14
AnsweredACulvert#268318Some blocks not displayed1402026-09-14
AnsweredACulvert#268317Tank load for surcharge and moving loads3402026-09-14
Sign in to ask